Aquasweep S10

The Aquasweep S10 is a cordless, chargeable handheld vacuum designed for easy, routine cleaning of pools and spas. It features a 120-micron filter and includes a corner head for corners, a floor brush for the pool bottom, and the option to use either the included telescopic pole for deeper sections or the short handle for spas and shallow areas.

Yes, the Aquasweep S10 can be used in above-ground pools, in-ground pools, hot tubs, and spas. It’s also safe to use in saltwater pools.

The S10 operates in water depths from 10 inches to 8.2 feet and works best in temperatures between 32°F and 104°F.

The Aquasweep S10 is designed to collect small debris like leaves, sand and bugs for daily maintenance. To treat algae, we recommend consulting with a pool technician for a chemical treatment plan.

Charge indoors in a clean, dry, ventilated area (41°F–95°F). Never use the cleaner while it’s charging.

1. 1. Turn off the S10 before charging.
   2. If recently used, tilt it to drain excess water.
   3. Make sure the unit and charging port are completely dry.
   4. Lift the soft seal and plug in the charger.
   5. Flashing red = charging, steady blue = fully charged

It takes about 4-5 hours to fully charge. When fully charged, the device operates for 60 minutes on Regular Mode and 30 minutes on Turbo Mode.

Always turn off and unplug from the charger before cleaning, filter replacement or any routine maintenance.

1. 1. Turn off the Aquasweep S10, lift the filter lock, and open the cover.
   2. Remove the filter, keeping it facing upward to avoid debris spilling out.
   3. Empty debris, then rinse the filter and the filter cover with clean water.
   4. Return the filter and the filter cover to the filter box.
   5. Lower the filter cover lock handle to lock it.

Use the Aquasweep S10 with the short handle and the corner head to clean pool edges and the floor brush to scrub and suction dirt from the bottom. Attach the extension pole for deep areas.

To attach the short handle:

1. 1. Attach the handle by pressing the release button and insert it into the back handle of the main body.
   2. If you want to remove the handle, press the release button and remove the handle.

To attach the telescopic pole:

1. 1. Squeeze the buckle to attach the extension adapter to the pole.
   2. Adjust until locked, 'click' into place.
   3. Press the buckle to connect it to the Aquasweep S10.
   4. To remove, press the buckles and detach.
   5. Rotate OPEN to extend, LOCK to secure.

The Aquasweep S10 is designed to pick up small debris such as leaves, sand, and bugs for everyday pool maintenance. For the best performance, empty the filter regularly and make sure the floor brush is clear of any blockage. You can run the cleaner multiple times for a deeper clean, and always keep it fully submerged (at least 10 inches) during use.

Make sure the Aquasweep S10 is fully charged before use (steady blue light on LED indicator).

Ensure it is submerged in water (at least 10"). If it is out of water, it will shut down within 15 seconds as out-of-water protection.

Steady Blue: Fully Charged/Regular Mode

Flashing Blue: Battery is starting to run low

Flashing Red: Charging

Steady Red: Low Battery (Less than 10% battery left)

No light: Fully drained

Purple Light: Turbo Mode

The Aquasweep S10 helps keep your pool floor clear of everyday dirt and debris. For reliable performance, start with a clean filter, fully submerge the unit within 15 seconds after switching it on, and ensure it’s used within the recommended water depth and temperature range. Avoid picking up large or sharp objects to prevent damage to the unit.

Store in an area protected from direct sunlight/rain/frost at storage temperature 32˚−104˚ F.

The S10 has Regular mode and Turbo Mode. If the device is fully charged, the Aquasweep S10 will work for 60 minutes in Regular Mode and for 30 minutes in Turbo Mode.

The telescopic pole included with the Aquasweep S10 extends from 33.5 inches to 69 inches. You can also attach a standard pool pole to extend the vacuum's reach.